View LT1766EGNTRPBF_8467787.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

lt1766/lt1766-5 1 1766fc typical application description 5.5v to 60v 1.5a, 200khz step-down switching regulator 5v buck converter features applications n wide input range: 5.5v to 60v n 1.5a peak switch current n constant 200khz switching frequency n saturating switch design: 0.2 n peak switch current rating maintained over full duty cycle range n low effective supply current: 2.5ma n low shutdown current: 25a n 1.2v feedback reference voltage (lt1766) n 5v fixed output (lt1766-5) n easily synchronizable n cycle-by-cycle current limiting n small 16-pin ssop and thermally enhanced tssop packages the lt ? 1766/lt1766-5 are 200khz monolithic buck switch- ing regulators that accept input voltages up to 60v. a high ef? ciency 1.5a, 0.2 switch is included on the die along with all the necessary oscillator, control and logic circuitry. a current mode control architecture delivers fast transient response and excellent loop stability. special design techniques and a new high voltage process achieve high ef? ciency over a wide input range. ef? ciency is maintained over a wide output current range by using the output to bias the circuitry and by utilizing a supply boost capacitor to saturate the power switch. patented circuitry maintains peak switch current over the full duty cycle range. a shutdown pin reduces supply current to 25a and the device can be externally synchronized from 228khz to 700khz with logic-level inputs. the lt1766/lt1766-5 are available in a 16-pin fused-lead ssop package or a tssop package with exposed backside for improved thermal performance. n high voltage, industrial and automotive n portable computers n battery-powered systems n battery chargers n distributed power systems ef? ciency vs load current boost v in 6 210 12 10mq060n 15.4k v out 5v1a 4 1514 11 220pf 0.022f * ? for input voltages below 7.5v, some restrictions may applytdk c4532x7r2a225k 1, 8, 9, 16 lt1766 shdnsync sw bias fb v c gnd 0.33f 100f 10vsolid tantalum 47h 1n4148w 4.99k 1766 ta01 2.2f ? 100vceramic v in * 5.5v to 60v + 2.2k on off load current (a) 0 efficiency (%) 80 90 100 1.00 1766 ta02 70 60 50 0.25 0.50 0.75 1.25 v in = 12v v in = 42v v out = 5v l = 47h l , lt, ltc, ltm, linear technology and the linear logo are registered trademarks and thinsot is a trademark of linear technology corporation. all other trademarks are the property of their respective owners. protected by u.s. patents, including 6498466, 6531909. downloaded from: http:///
lt1766/lt1766-5 2 1766fc absolute maximum ratings (note 1) input voltage (v in ) .................................................. 60v boost pin above sw .............................................. 35v boost pin voltage ................................................. 68v sync, sense voltage (lt1766-5) ............................. 7v shdn voltage ............................................................ 6v bias pin voltage ..................................................... 30v fb pin voltage/current (lt1766) ................... 3.5v/2ma operating junction temperature range lt1766efe/lt1766efe-5/lt1766egn/ lt1766egn-5 (note 8,10) ....................C40c to 125c lt1766ife/lt1766ife-5/ lt1766ign/lt1766ign-5 (note 8,10) ..C40c to 125c lt1766hfe ..........................................C40c to 140c storage temperature range .................. C65c to 150c lead temperature (soldering, 10 sec) .................. 300c fe package 16-lead plastic tssop 12 3 4 5 6 7 8 top view 1615 14 13 12 11 10 9 gnd sw nc v in nc boost nc gnd gndshdn sync nc fb/sense v c biasgnd 17 gnd ja = 45c, jc (pin 17) = 10c/w exposed pad (pin 17) is gnd, must be soldered to pcb gn package 16-lead plastic ssop 12 3 4 5 6 7 8 top view 1615 14 13 12 11 10 9 gnd sw nc v in nc boost nc gnd gndshdn sync nc fb/sense v c biasgnd ja = 85c, jc (pin 8) = 25c/w four corner pins soldered to ground pin pin configuration downloaded from: http:///
lt1766/lt1766-5 3 1766fc electrical characteristics the l denotes speci? cations which apply over the full operating temperature range, otherwise speci? cations are at t j = 25c. v in = 15v, vc = 1.5v, shdn = 1v, boost open circuit, sw open circuit, unless otherwise noted. parameter conditions min typ max units reference voltage (v ref ) (lt1766) 5.5v v in 60v v ol + 0.2 v c v oh C 0.2 l 1.2041.195 1.219 1.234 1.243 vv sense voltage (lt1766-5) 5.5v v in 60v v ol + 0.2v v c v oh C 0.2v l 4.944.90 5 5.06 5.10 vv sense pin resistance (lt1766-5) 9.5 13.8 19 k fb input bias current (lt1766) l C0.5 C1.5 a error amp voltage gain (notes 2, 9) 200 400 v/v error amp g m dl (v c ) = 10a (note 9) l 15001000 2000 3000 4200 mhomho v c to switch g m 1.7 a/v ea source current fb = 1v or v sense = 4.1v l 125 225 400 a ea sink current fb = 1.4v or v sense = 5.7v l 100 225 450 a v c switching threshold duty cycle = 0 0.9 v v c high clamp shdn = 1v 2.1 v switch current limit v c open, boost = v in + 5v, fb = 1v or v sense = 4.1v l 1.5 2 3 a order information lead free finish tape and reel part marking package description temperature range lt1766efe#pbf lt1766efe#trpbf 1766efe 16-lead plastic tssop 0c to 125c lt1766ife#pbf lt1766ife#trpbf 1766ife 16-lead plastic tssop C40c to 125c lt1766hfe#pbf lt1766hfe#trpbf 1766hfe 16-lead plastic tssop C40c to 140c lt1766efe-5#pbf lt1766efe-5#trpbf 1766efe-5 16-lead plastic tssop 0c to 125c lt1766ife-5#pbf lt1766ife-5#trpbf 1766ife-5 16-lead plastic tssop C40c to 125c lt1766egn#pbf lt1766egn#trpbf 1766 16-lead plastic ssop 0c to 125c lt1766ign#pbf lt1766ign#trpbf 1766i 16-lead plastic ssop C40c to 125c lt1766egn-5#pbf lt1766egn-5#trpbf 17665 16-lead plastic ssop 0c to 125c lt1766ign-5#pbf lt1766ign-5#trpbf 1766i5 16-lead plastic ssop C40c to 125c lead based finish tape and reel part marking package description temperature range lt1766efe lt1766efe#tr 1766efe 16-lead plastic tssop 0c to 125c lt1766ife lt1766ife#tr 1766ife 16-lead plastic tssop C40c to 85c lt1766hfe lt1766hfe#tr 1766hfe 16-lead plastic tssop C40c to 140c lt1766efe-5 lt1766efe-5#tr 1766efe-5 16-lead plastic tssop 0c to 125c lt1766ife-5 lt1766ife-5#tr 1766ife-5 16-lead plastic tssop C40c to 125c lt1766egn lt1766egn#tr 1766 16-lead plastic ssop 0c to 125c lt1766ign lt1766ign#tr 1766i 16-lead plastic ssop C40c to 125c lt1766egn-5 lt1766egn-5#tr 17665 16-lead plastic ssop 0c to 125c lt1766ign-5 lt1766ign-5#tr 1766i5 16-lead plastic ssop C40c to 125c consult ltc marketing for parts speci? ed with wider operating temperature ranges. for more information on lead free part marking, go to: http://www.linear.com/leadfree/ for more information on tape and reel speci? cations, go to: http://www.linear.com/tapeandreel/ (lt1766e/lt1766i grade) downloaded from: http:///
lt1766/lt1766-5 4 1766fc parameter conditions min typ max units reference voltage (v ref ) 5.5v v in 60v v ol + 0.2 v c v oh C 0.2 l 1.2041.175 1.219 1.234 1.265 vv fb input bias current l C0.5 C1.5 a error amp voltage gain (notes 2, 9) 200 400 v/v error amp g m dl (v c ) = 10a (note 9) l 1500 900 2000 3000 4200 mhomho v c to switch g m 1.7 a/v ea source current fb = 1v or v sense = 4.1v l 125 225 400 a ea sink current fb = 1.4v or v sense = 5.7v l 100 225 450 a v c switching threshold duty cycle = 0 0.9 v v c high clamp shdn = 1v 2.1 v switch current limit v c open, boost = v in + 5v, fb = 1v or v sense = 4.1v l 0.75 2 3 a switch on resistance i sw = 0.75a, boost = v in + 5v (note 7) l 0.2 0.3 0.8 ? maximum switch duty cycle fb = 1v or v sense = 4.1v l 9390 96 % % switch frequency v c set to give dc = 50% l 184135 200200 216228 khzkhz (lt1766h grade) the l denotes speci? cations which apply over the full operating temperature range, otherwise speci? cations are at t j = 25c. v in = 15v, v c = 1.5v, shdn = 1v, boost open circuit, sw open circuit, unless otherwise noted. parameter conditions min typ max units switch on-resistance i sw = 1.5a, boost = v in + 5v (note 7) l 0.2 0.3 0.4 maximum switch duty cycle fb = 1v or v sense = 4.1v l 9390 96 % % switch frequency v c set to give dc = 50% l 184172 200200 216228 khzkhz f sw line regulation 5.5v v in 60v l 0.05 0.15 %/v f sw frequency shifting threshold df = 10khz 0.8 v minimum input voltage (note 3) l 4.6 5.5 v minimum boost voltage (note 4) i sw 1.5a l 1.8 3 v boost current (note 5) boost = v in + 5v, i sw = 0.5a boost = v in + 5v, i sw = 1.5a ll 1245 2570 mama input supply current (i vin ) (note 6) v bias = 5v 1.4 2.2 ma bias supply current (i bias ) (note 6) v bias = 5v 2.9 4.2 ma shutdown supply current shdn = 0v, v in 60v, sw = 0v, v c open l 25 75 200 aa lockout threshold v c open l 2.3 2.42 2.53 v shutdown thresholds v c open, shutting down v c open, starting up ll 0.150.25 0.370.45 0.60.6 vv minimum sync amplitude l 1.5 2.2 v sync frequency range 228 700 khz sync input resistance 20 k electrical characteristics the l denotes speci? cations which apply over the full operating temperature range, otherwise speci? cations are at t j = 25c. v in = 15v, v c = 1.5v, shdn = 1v, boost open circuit, sw open circuit, unless otherwise noted. (lt1766e/lt1766i grade) downloaded from: http:///
lt1766/lt1766-5 5 1766fc electrical characteristics parameter conditions min typ max units f sw line regulation 5.5v v in 60v l 0.05 0.15 %/v f sw frequency shifting threshold df = 10khz 0.8 v minimum input voltage (note 3) l 4.6 5.5 v minimum boost voltage (note 4) i sw 0.75a l 1.8 3 v boost current (note 5) boost = v in + 5v, i sw = 0.5a boost = v in + 5v, i sw = 0.75a ll 1245 40 100 mama input supply current (i vin ) (note 6) v bias = 5v 1.4 2.2 ma bias supply current (i bias ) (note 6) v bias = 5v 2.9 4.2 ma shutdown supply current shdn = 0v, v in 60v, sw = 0v, v c open l 25 120 500 aa lockout threshold v c open l 2.3 2.42 2.68 v shutdown thresholds v c open, shutting down v c open, starting up ll 0.150.25 0.370.45 0.90.9 vv minimum sync amplitude l 1.5 2.2 v sync frequency range 228 700 khz sync input resistance 20 k (lt1766h grade) the l denotes speci? cations which apply over the full operating temperature range, otherwise speci? cations are at t j = 25c. v in = 15v, v c = 1.5v, shdn = 1v, boost open circuit, sw open circuit, unless otherwise noted. note 1: stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. exposure to any absolute maximum rating condition for extended periods may affect device reliability and lifetime. note 2: gain is measured with a v c swing equal to 200mv above the low clamp level to 200mv below the upper clamp level.note 3: minimum input voltage is not measured directly, but is guaranteed by other tests. it is de? ned as the voltage where internal bias lines are still regulated so that the reference voltage and oscillator remain constant. actual minimum input voltage to maintain a regulated output will depend upon output voltage and load current. see applications information. note 4: this is the minimum voltage across the boost capacitor needed to guarantee full saturation of the internal power switch.note 5: boost current is the current ? owing into the boost pin with the pin held 5v above input voltage. it ? ows only during switch on time. note 6: input supply current is the quiescent current drawn by the input pin when the bias pin is held at 5v with switching disabled. bias supply current is the current drawn by the bias pin when the bias pin is held at 5v. total input referred supply current is calculated by summing input supply current (i vin ) with a fraction of bias supply current (i bias ): i total = i vin + (i bias )(v out /v in ) with v in = 15v, v out = 5v, i vin = 1.4ma, i bias = 2.9ma, i total = 2.4ma. note 7: switch on-resistance is calculated by dividing v in to sw voltage by the forced current. see typical performance characteristics for the graph of switch voltage at other currents. note 8: the lt1766egn, lt1766egn-5, lt1766efe and lt1766efe-5 are guaranteed to meet performance speci? cations from 0c to 125c junction temperature. speci? cations over the C40c to 125c operating junction temperature range are assured by design, characterization and correlation with statistical process controls. the lt1766ign, lt1766ign-5, lt1766ife and lt1766ife-5 are guaranteed over the full C40c to 125c operating junction temperature range. the lt1766hgn and lt1766hfe are guaranteed over the full C40c to 140c operating junction temperature range. note 9: transconductance and voltage gain refer to the internal ampli? er exclusive of the voltage divider. to calculate gain and transconductance, refer to the sense pin on ? xed voltage parts. divide the values shown by the ratio v out /1.219. note 10: this ic includes overtemperature protection that is intended to protect the device during momentary overload conditions. junction temperature will exceed 140c when overtemperature protection is active. continuous operation above the speci? ed maximum operating junction temperature may impair device reliability. note 11: high junction temperatures degrade operating lifetimes. operating lifetime at junction temperatures between 125c and 140c is derated to 1000 hours. downloaded from: http:///
lt1766/lt1766-5 6 1766fc duty cycle (%) 1.0 switch peak current (a) 1.5 2.0 2.5 20 40 typical 60 80 1766 g01 100 0 guaranteed minimum t a = 25c junction temperature (c) C50 feedback voltage (v) current (a) 1.224 1.229 1.234 25 75 1766 g02 1.219 1.214 C25 0 50 100 125 150 1.209 1.204 1.5 2.0 1.0 0.5 0 voltage current junction temperature (c) C50 250200 150 100 12 60 25 75 1766 g03 C25 0 50 100 150 125 current (a) current required to force shutdown(flows out of pin). after shutdown, current drops to a few a at 2.38v standby threshold(current flows out of pin) typical performance characteristics switch peak current limit shdn pin bias current shutdown supply current lockout and shutdown thresholds shutdown supply current error ampli? er transconductance fb pin voltage and current error ampli? er transconductance junction temperature (c) C50 shdn pin voltage (v) 50 100 1766 g04 0 25 75 2.42.0 1.6 1.2 0.8 0.4 0 C25 150 125 lockout start-up shutdown input voltage (v) 0 input supply current (a) 1766 g05 10 20 30 40 50 60 4035 30 25 20 15 10 50 v shdn = 0v t a = 25c shutdown voltage (v) 0 0 input supply current (a) 50 100 150 200 250 300 0.1 0.2 0.3 0.4 1766 g06 0.5 v in = 60v v in = 15v t a = 25c junction temperature (c) transconductance (mho) 1766 g07 25002000 1500 1000 500 0 C50 50 100 0 25 75 C25 150 125 frequency (hz) gain (mho) phase (deg) 30002500 2000 1500 1000 500 200150 100 50 0 C50 100 10k 100k 10m 1766 g08 1k 1m gain phase error amplifier equivalent circuit r out 200k c out 12pf v c r load = 50 v fb 2 ? 10 C3 ) ( t a = 25 c v fb (v) 0 switiching frequency (khz) or fb current (a) 300 400 600500 1766 g09 200 100 0 0.5 1.0 1.5 switching frequency fb pin current t a = 25c frequency foldback downloaded from: http:///
lt1766/lt1766-5 7 1766fc pin functions typical performance characteristics switching frequency boost pin current minimum input voltage with 5v output switch voltage drop junction temperature (c) C50 frequency (khz) 50 100 1766 g10 0 25 75 230220 210 200 190 180 170 C25 150 125 load current (a) 0 input voltage (v) 1766 g11 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1 7.57.0 6.5 6.0 5.5 5.0 minimum inputvoltage to start minimum inputvoltage to run t a = 25c switch current (a) 0 0.5 1 1.5 boost pin current (ma) 1766 g12 4540 35 30 25 20 15 10 50 t a = 25c junction temperature (c) C50 1.5 1.7 2.1 25 75 1766 g13 1.31.1 C25 0 50 100 150 125 0.9 0.7 1.9 threshold voltage (v) switch current (a) 0 0.5 1 1.5 switch voltage (mv) 1766 g14 450400 350 300 250 200 150 100 50 0 t j = 125c t j = 150c t j = 25c t j = C40c junction temperature (c) C50 switch minimum on time (ns) 400 500 600 25 75 1766 g15 300 200 C25 0 50 100 150 125 100 0 v c pin shutdown threshold switch minimum on-time vs temperature gnd (pins 1, 8, 9, 16, 17): the gnd pin connections act as the reference for the regulated output, so load regula-tion will suffer if the ground end of the load is not at the same voltage as the gnd pins of the ic. this condition will occur when load current or other currents ? ow through metal paths between the gnd pins and the load ground. keep the paths between the gnd pins and the load ground short and use a ground plane when possible. the gnd pin also acts as a heat sink and should be soldered to a large copper plane to reduce thermal resistance. for the fe package, the exposed pad should be soldered to the copper ground plane underneath the device. (see applica-tions informationlayout considerations.) sw (pin 2): the switch pin is the emitter of the on-chip power npn switch. this pin is driven up to the input pin voltage during switch on-time. inductor current drives the switch pin negative during switch off-time. negative volt- age is clamped with the external catch diode. maximum negative switch voltage allowed is C 0.8v. nc (pins 3, 5, 7, 13): no connection. downloaded from: http:///
lt1766/lt1766-5 8 1766fc pin functions block diagram v in (pin 4): this is the collector of the on-chip power npn switch. v in powers the internal control circuitry when a voltage on the bias pin is not present. high di/dt edges occur on this pin during switch turn on and off. keep the path short from the v in pin through the input bypass capacitor, through the catch diode back to sw. all trace inductance on this path will create a voltage spike at switch off, adding to the v ce voltage across the internal npn. boost (pin 6): the boost pin is used to provide a drive voltage, higher than the input voltage, to the internal bipolar npn power switch. without this added voltage, the typical switch voltage loss would be about 1.5v. the additional boost voltage allows the switch to saturate and voltage loss approximates that of a 0.2 fet structure, but with much smaller die area. bias (pin 10): the bias pin is used to improve ef? ciency when operating at higher input voltages and light load cur- rent. connecting this pin to the regulated output voltage forces most of the internal circuitry to draw its operating current from the output voltage rather than the input supply. this architecture increases ef? ciency especially when the input voltage is much higher than the output. minimum output voltage setting for this mode of operation is 3v. v c (pin 11) the v c pin is the output of the error ampli? er and the input of the peak switch current comparator. it is normally used for frequency compensation, but can also serve as a current clamp or control loop override. v c sits at about 0.9v for light loads and 2.1v at maximum load. it can be driven to ground to shut off the regulator, but if driven high, current must be limited to 4ma. fb/sense (pin 12): the feedback pin is used to set the output voltage using an external voltage divider that gener- ates 1.22v at the pin for the desired output voltage. the 5v ? xed output voltage parts have the divider included on the chip and the fb pin is used as a sense pin, connected directly to the 5v output. three additional functions are performed by the fb pin. when the pin voltage drops below 0.6v, switch current limit is reduced and the external sync function is disabled. below 0.8v, switching frequency is also reduced. see feedback pin functions in applications information for details. sync (pin 14): the sync pin is used to synchronize the internal oscillator to an external signal. it is directly logic compatible and can be driven with any signal between 10% and 90% duty cycle. the synchronizing range is equal to initial operating frequency up to 700khz. see synchroniz- ing in applications information for details. shdn (pin 15): the shdn pin is used to turn off the regulator and to reduce input drain current to a few mi-croamperes. this pin has two thresholds: one at 2.38v to disable switching and a second at 0.4v to force complete micropower shutdown. the 2.38v threshold functions as an accurate undervoltage lockout (uvlo); sometimes used to prevent the regulator from delivering power until the input voltage has reached a predetermined level. if the shdn pin functions are not required, the pin can either be left open (to allow an internal bias current to lift the pin to a default high state) or be forced high to a level not to exceed 6v. the lt1766 is a constant frequency, current mode buck converter. this means that there is an internal clock and two feedback loops that control the duty cycle of the power switch. in addition to the normal error ampli? er, there is a current sense ampli? er that monitors switch current on a cycle-by-cycle basis. a switch cycle starts with an oscillator pulse which sets the r s ? ip-? op to turn the switch on. when switch current reaches a level set by the inverting input of the comparator, the ? ip-? op is reset and the switch turns off. output voltage control is obtained by using the output of the error ampli? er to set the switch current trip point. this technique means that the error ampli? er commands current to be delivered to the output rather than voltage. a voltage fed system will have low phase shift up to the resonant frequency of the inductor and output capacitor, then an abrupt 180 shift will occur. the current fed system downloaded from: http:///
lt1766/lt1766-5 9 1766fc block diagram will have 90 phase shift at a much lower frequency, but will not have the additional 90 shift until well beyond the lc resonant frequency. this makes it much easier to frequency compensate the feedback loop and also gives much quicker transient response. most of the circuitry of the lt1766 operates from an internal 2.9v bias line. the bias regulator normally draws power from the regulator input pin, but if the bias pin is connected to an external voltage higher than 3v, bias power will be drawn from the external source (typically the regulated C + C + C + C + v in 2.9v bias regulator 200khz oscillator frequency foldback sw fbgnd 1, 8, 9, 16, 17 1766 f01 slope comp antislope comp bias internalv cc sync 0.4v 5.5a currentcomparator r limit r sense error amplifier g m = 2000mho q2 foldback current limit clamp boost r s flip-flop driver circuitry sr q1power switch 1.22v 4 10 14 shdn 15 6 2 12 11 v c lockout comparator shutdown comparator 2.38v 1 q3 v c(max) clamp output voltage). this will improve ef? ciency if the bias pin voltage is lower than regulator input voltage. high switch ef? ciency is attained by using the boost pin to provide a voltage to the switch driver which is higher than the input voltage, allowing switch to be satu- rated. this boosted voltage is generated with an external capacitor and diode. two comparators are connected to the shutdown pin. one has a 2.38v threshold for undervoltage lockout and the second has a 0.4v threshold for complete shutdown. figure 1. lt1766 block diagram downloaded from: http:///
lt1766/lt1766-5 10 1766fc applications information feedback pin functions the feedback (fb) pin on the lt1766 is used to set output voltage and provide several overload protection features. the ? rst part of this section deals with selecting resistors to set output voltage and the remaining part talks about foldback frequency and current limiting created by the fb pin. please read both parts before committing to a ? nal design. the 5v ? xed output voltage part (lt1766-5) has internal divider resistors and the fb pin is renamed sense, connected directly to the output. the suggested value for the output divider resistor (see figure 2) from fb to ground (r2) is 5k or less, and a formula for r1 is shown below. the output voltage error caused by ignoring the input bias current on the fb pin is less than 0.25% with r2 = 5k. a table of standard 1% values is shown in table 1 for common output voltages. please read the following if divider resistors are increased above the suggested values. r rv out 1 21 2 2 122 = () . . table 1 output voltage (v) r2 (k) r1 (nearest 1%) (k) % error at output due to discreet 1% resistor steps 34 . 9 97 . 3 2 + 0 . 3 2 3.3 4.99 8.45 C0.43 54 . 9 91 5 . 4 C 0 . 3 0 64 . 7 51 8 . 7 + 0 . 3 8 84 . 4 72 4 . 9 + 0 . 2 0 10 4.32 30.9 C0.54 12 4.12 36.5 +0.24 15 4.12 46.4 C0.27 more than just voltage feedback the feedback pin is used for more than just output voltage sensing. it also reduces switching frequency and current limit when output voltage is very low (see the frequency foldback graph in typical performance characteristics). this is done to control power dissipation in both the ic and in the external diode and inductor during short-cir- cuit conditions. a shorted output requires the switching regulator to operate at very low duty cycles, and the average current through the diode and inductor is equal to the short-circuit current limit of the switch (typically 2a for the lt1766, folding back to less than 1a). minimum switch on-time limitations would prevent the switcher from attaining a suf? ciently low duty cycle if switching frequency were maintained at 200khz, so frequency is reduced by about 5:1 when the feedback pin voltage drops below 0.8v (see frequency foldback graph). this does not affect operation with normal load conditions; one simply sees a gear shift in switching frequency during start-up as the output voltage rises. in addition to lower switching frequency, the lt1766 also operates at lower switch current limit when the feedback pin voltage drops below 0.6v. q2 in figure 2 performs this function by clamping the v c pin to a voltage less than its normal 2.1v upper clamp level. this foldback current limit greatly reduces power dissipation in the ic, diode and inductor during short-circuit conditions. external syn- chronization is also disabled to prevent interference with foldback operation. again, it is nearly transparent to the user under normal load conditions. the only loads that may be affected are current source loads which maintain full load current with output voltage less than 50% of ? nal value. in these rare situations the feedback pin can be clamped above 0.6v with an external diode to defeat foldback cur- rent limit. caution: clamping the feedback pin means that frequency shifting will also be defeated, so a combination of high input voltage and dead shorted output may cause the lt1766 to lose control of current limit. the internal circuitry which forces reduced switching frequency also causes current to ? ow out of the feedback pin when output voltage is low. the equivalent circuitry is shown in figure 2. q1 is completely off during normal op- eration. if the fb pin falls below 0.8v, q1 begins to conduct current and reduces frequency at the rate of approximately 1.4khz/a. to ensure adequate frequency foldback (under worst-case short-circuit conditions), the external divider thevinin resistance must be low enough to pull 115a out of the fb pin with 0.44v on the pin (r div 3.8k). the net result is that reductions in frequency and current limit are affected by output voltage divider impedance. although downloaded from: http:///
lt1766/lt1766-5 11 1766fc applications information divider impedance is not critical, caution should be used if resistors are increased beyond the suggested values and short-circuit conditions occur with high input voltage. high frequency pickup will increase and the protection accorded by frequency and current foldback will decrease. choosing the inductor for most applications, the output inductor will fall into the range of 15h to 100h. lower values are chosen to reduce physical size of the inductor. higher values allow more output current because they reduce peak current seen by the lt1766 switch, which has a 1.5a limit. higher values also reduce output ripple voltage. when choosing an inductor you will need to consider output ripple voltage, maximum load current, peak induc- tor current and fault current in the inductor. in addition, other factors such as core and copper losses, allowable component height, emi, saturation and cost should also be considered. the following procedure is suggested as a way of handling these somewhat complicated and con? icting requirements. output ripple voltage figure 3 shows a typical output ripple voltage wave- form for the lt1766. ripple voltage is determined by ripple current (i lp-p ) through the inductor and the high frequency impedance of the output capacitor. the fol- lowing equations will help in choosing the required inductor value to achieve a desirable output ripple volt-age level. if output ripple voltage is of less importance, the subsequent suggestions in peak inductor and fault current and emi will additionally help in the selection of the inductor value. peak-to-peak output ripple voltage is the sum of a triwave (created by peak-to-peak ripple current (i lp-p ) times esr) and a square wave (created by parasitic inductance (esl) and ripple current slew rate). capacitive reactance is as- sumed to be small compared to esr or esl. v i esr esl di dt ripple lp p = () () + () - figure 2. frequency and current limit foldback C + 1.2v buffer v sw l1 v c gnd to sync circuit 1766 f02 to frequency shifting r3 1k r42k r1 c1 r25k output5v error amplifier fb 1.4v q1 lt1766 q2 + figure 3. lt1766 ripple voltage waveform 2.5s/div 40mv/div v out at i out = 1a v out at i out = 0.1a inductor currentat i out = 1a inductor currentat i out = 0.1a 0.5a/div v in = 40v v out = 5v l = 47hc = 100f, 10v, 0.1 1766 f03 downloaded from: http:///
lt1766/lt1766-5 12 1766fc if maximum load current is 0.5a, for instance, a 0.5a inductor may not survive a continuous 2a overload con- dition. dead shorts will actually be more gentle on the inductor because the lt1766 has frequency and current limit foldback. peak switch and inductor current can be signi? cantly higher than output current, especially with smaller inductors and lighter loads, so dont omit this step. powdered iron cores are forgiving because they saturate softly, whereas ferrite cores saturate abruptly. other core materials fall somewhere in between. the following formula assumes continuous mode of operation, but errs only slightly on where: esr = equivalent series resistance of the output capacitor esl = equivalent series inductance of the output capacitor di/dt = slew rate of inductor ripple current = v in /l peak-to-peak ripple current (i lp-p ) through the inductor and into the output capacitor is typically chosen to be between 20% and 40% of the maximum load current. it is approximated by: i vvv vfl lp p out in out in - = () ( ) () () () ? example: with v in = 40v, v out = 5v, l = 47h, esr = 0.1 and esl = 10nh, output ripple voltage can be approximated as follows: ia di dt va mv ripple p-p p-p = () () () () () = == = () ( ) + () ( ) () =+= 540 5 40 47 10 200 10 0 465 40 47 10 10 0 85 0 465 0 1 10 10 10 0 85 0 0465 0 0085 55 63 6 6 96 ?? . ? ?. ..? . .. to reduce output ripple voltage further requires an increase in the inductor value or a reduction in the capacitor esr. the latter can effect loop stability since the esr forms a useful zero in the overall loop response. typically the inductor value is adjusted with the trade-off being a physically larger inductor with the possibility of increased component height and cost. choosing a smaller inductor with lighter loads may result in discontinuous operation but the lt1766 is designed to work well in both continuous or discontinuous mode. peak inductor current and fault current to ensure that the inductor will not saturate, the peak inductor current should be calculated knowing the maximum load current. an appropriate inductor should then be chosen. in addition, a decision should be made whether or not the inductor must withstand continuous fault conditions. applications information table 2 vendor/ part no. value (h) i dc (amps) dcr (ohms) height (mm) coiltronics ctx15-1p 15 1.4 0.087 4.2 ctx15-1 15 1.1 0.08 4.2 ctx33-2p 33 1.3 0.126 6 ctx33-2 33 1.4 0.106 6 up2-330 33 2.4 0.099 5.9 up2-470 47 1.9 0.146 5.9 up2-680 68 1.7 0.19 5.9 up2-101 100 1.4 0.277 5.9 sumida cdrh6d28-150m 15 1.4 0.076 3 cdrh6d38-150m 15 1.6 0.062 4 cdrh6d28-330m 33 0.97 0.122 3 cdrh104r-330m 33 2.1 0.069 3.8 cdrh125-330m 33 2.1 0.044 6 cdrh104r-470m 47 2.1 0.095 3.8 cdrh125-470m 47 1.8 0.058 6 cdrh6d38-680m 68 0.75 0.173 4 cdrh104r-680m 68 1.5 0.158 3.8 cdrh125-680m 68 1.5 0.093 6 cdrh104r-101m 100 1.35 0.225 3.8 cdrh125-101m 100 1.3 0.120 6 coilcraft dt3316p-153 15 1.8 0.06 5 dt3316p-333 33 1.3 0.09 5 dt3316p-473 47 1 0.11 5 downloaded from: http:///
lt1766/lt1766-5 13 1766fc applications information the high side for discontinuous mode, so it can be used for all conditions. ii i i vvv vfl peak out lp p out out in out in =+ =+ () ( ) ()( )()() () ? - 2 2 emidecide if the design can tolerate an open core geometry like a rod or barrel, which have high magnetic ? eld radiation, or whether it needs a closed core like a toroid to prevent emi problems. this is a tough decision because the rods or barrels are temptingly cheap and small and there are no helpful guidelines to calculate when the magnetic ? eld radiation will be a problem.additional considerations after making an initial choice, consider additional factors such as core losses and second sourcing, etc. use the experts in linear technologys applications department if you feel uncertain about the ? nal choice. they have experience with a wide range of inductor types and can tell you about the latest developments in low pro? le, surface mounting, etc.maximum output load current maximum load current for a buck converter is limited by the maximum switch current rating (i p ). the current rating for the lt1766 is 1.5a. unlike most current mode converters, the lt1766 maximum switch current limit does not fall off at high duty cycles. most current mode converters suffer a drop off of peak switch current for duty cycles above 50%. this is due to the effects of slope compensation required to prevent subharmonic oscilla- tions in current mode converters. (for detailed analysis, see application note 19.) the lt1766 is able to maintain peak switch current limit over the full duty cycle range by using patented circuitry* to cancel the effects of slope compensation on peak switch current without affecting the frequency compensation it provides. maximum load current would be equal to maximum switch current for an in? nitely large inductor , but with ? nite inductor size, maximum load current is reduced by one-half peak-to-peak inductor current (i lp-p ). the following formula assumes continuous mode operation, implying that the term on the right is less than one-half of i p . i out(max) = continuous mode i? i 2 = i p lp-p p + () () ()()( ) vvvvv lfv out f in out f in ? 2 for v out = 5v, v in = 8v, v f(d1) = 0.63v, f = 200khz and l = 20h: i a out max () = + () () () () () = = 15 5 0 63 8 5 0 63 2 20 10 200 10 8 15 021 129 63 . .? . ?? .. . note that there is less load current available at the higher input voltage because inductor ripple current increases. at v in = 15v, duty cycle is 33% and for the same set of conditions: i a out max () . .? . ?? .. . = + () () () () () = = 15 5 0 63 15 5 0 63 2 20 10 200 10 15 15 044 106 63 to calculate actual peak switch current with a given set of conditions, use: ii i vv vvv lfv sw peak out p out out f in out f in () =+ =+ + () ()()( ) i 2 l-p () ? 2 reduced inductor value and discontinuous mode if the smallest inductor value is of most importance to a converter design, in order to reduce inductor size/cost, discontinuous mode may yield the smallest inductor solu- tion. the maximum output load current in discontinuous mode, however, must be calculated and is de? ned later in this section. *patent # 6, 498, 466 downloaded from: http:///
lt1766/lt1766-5 14 1766fc discontinuous mode is entered when the output load current is less than one-half of the inductor ripple current (i lp-p ). in this mode, inductor current falls to zero before the next switch turn on (see figure 8). buck converters will be in discontinuous mode for output load current given by: i out discontinuous mode the inductor value in a buck converter is usually chosen large enough to keep inductor ripple current (i lp-p ) low; this is done to minimize output ripple voltage and maximize output load current. in the case of large inductor values, as seen in the equation above, discontinuous mode will be associated with light loads . when choosing small inductor values, however, discon- tinuous mode will occur at much higher output load cur- rents. the limit to the smallest inductor value that can be chosen is set by the lt1766 peak switch current (i p ) and the maximum output load current required, given by: i out(max) discontinuous mode example: for v in = 15v, v out = 5v, v f = 0.63v, f = 200khz and l = 10h. i out(max) discontinuous mode i out(max) = 0.639a discontinuous mode what has been shown here is that if high inductor ripple current and discontinuous mode operation can be tolerated, small inductor values can be used. if a higher output load current is required, the inductor value must be increased. if i out(max) no longer meets the discontinuous mode criteria, use the i out(max) equation for continuous mode; the lt1766 is designed to operate well in both modes of operation, allowing a large range of inductor values to be used. short-circuit considerations the lt1766 is a current mode controller. it uses the v c node voltage as an input to a current comparator which turns off the output switch on a cycle-by-cycle basis as this peak current is reached. the internal clamp on the v c node, nominally 2v, then acts as an output switch peak current limit. this action becomes the switch current limit speci? cation. the maximum available output power is then determined by the switch current limit.a potential controllability problem could occur under short-circuit conditions. if the power supply output is short circuited, the feedback ampli? er responds to the low output voltage by raising the control voltage, v c , to its peak current limit value. ideally, the output switch would be turned on, and then turned off as its current exceeded the value indicated by v c . however, there is ? nite response time involved in both the current comparator and turn-off of the output switch. these result in a minimum on-time, t on(min) . when combined with the large ratio of v in to (v f + i ? r), the diode forward voltage plus inductor i ? r voltage drop, the potential exists for a loss of control. expressed mathematically the requirement to maintain control is: ft vir v on f in ? ? + where: f = switching frequency t on = switch minimum on-time v f = diode forward voltage v in = input voltage i ? r = inductor i ? r voltage drop if this condition is not observed, the current will not be limited at i pk , but will cycle-by-cycle ratchet up to some higher value. using the nominal lt1766 clock frequency of 200khz, a v in of 40v and a (v f + i ? r) of say 0.7v, the maximum t on to maintain control would be approximately 90ns, an unacceptably short time.the solution to this dilemma is to slow down the oscil- lator when the fb pin voltage is abnormally low thereby indicating some sort of short-circuit condition. oscillator frequency is unaffected until fb voltage drops to about 2/3 of its normal value. below this point the oscillator < + () ( ? ? ) ()( )()() vvvvv vfl out f in out f in 2 == ()( ) + i iflv vvvvv p pi n out f in out f 2 2 2 2 ()( ) ()( )( ) () ( ? ? ) i lp-p = + (.)? (?) ( ) () (.) (??.) ? 1 5 200 10 10 15 25063155063 23 5 applications information downloaded from: http:///
lt1766/lt1766-5 15 1766fc capacitors fail during very high turn-on surges, which do not occur at the output of regulators. high discharge surges, such as when the regulator output is dead shorted, do not harm the capacitors. unlike the input capacitor, rms ripple current in the output capacitor is normally low enough that ripple current rating is not an issue. the current waveform is triangular with a typical value of 125ma rms . the formula to calculate this is:output capacitor ripple current (rms): i vvv lfv ripple rms out in out in () = () () ()()( ) 029 . ceramic capacitors higher value, lower cost ceramic capacitors are now becoming available. they are generally chosen for their good high frequency operation, small size and very low esr (effective series resistance). their low esr reduces output ripple voltage but also removes a useful zero in the loop frequency response, common to tantalum capaci- tors. to compensate for this, a resistor r c can be placed in series with the v c compensation capacitor, c c . care must be taken however, since this resistor sets the high frequency gain of the error ampli? er, including the gain at the switching frequency. if the gain of the error ampli? er is high enough at the switching frequency, output ripple voltage (although smaller for a ceramic output capacitor) may still affect the proper operation of the regulator. a ? lter capacitor, c f , in parallel with the r c /c c network is suggested to control possible ripple at the v c pin. an all ceramic solution is possible for the lt1766 by choos- ing the correct compensation components for the given application. example: for v in = 8v to 40v, v out = 3.3v at 1a, the lt1766 can be stabilized, provide good transient response and maintain very low output ripple voltage using the following component values: (refer to the ? rst page of this data sheet for component references) c3 = 2.2f, r c = 4.7k, c c = 15nf, c f = 220pf and c1 = 47f. see application note 19 for further detail on techniques for proper loop compensation. frequency decreases roughly linearly down to a limit of about 40khz. this lower oscillator frequency during short-circuit conditions can then maintain control with the effective minimum on time. it is recommended that for [v in /(v out + v f )] ratios > 10, a soft-start circuit should be used to control the output capacitor charge rate during start-up or during recovery from an output short circuit, thereby adding additional control over peak inductor current. see buck converter with adjustable soft-start later in this data sheet. output capacitor the output capacitor is normally chosen by its effective series resistance (esr), because this is what determines output ripple voltage. to get low esr takes volume , so physically smaller capacitors have high esr. the esr range for typical lt1766 applications is 0.05 to 0.2. a typical output capacitor is an avx type tps, 100f at 10v, with a guaranteed esr less than 0.1. this is a d size surface mount solid tantalum capacitor. tps capaci- tors are specially constructed and tested for low esr, so they give the lowest esr for a given volume. the value in microfarads is not particularly critical, and values from 22f to greater than 500f work well, but you cannot cheat mother nature on esr. if you ? nd a tiny 22f solid tantalum capacitor, it will have high esr, and output ripple voltage will be terrible. table 2 shows some typical solid tantalum surface mount capacitors. table 3. surface mount solid tantalum capacitor esr and ripple current e case size esr (max, ) ripple current (a) avx tps, sprague 593d 0.1 to 0.3 0.7 to 1.1 d case size avx tps, sprague 593d 0.1 to 0.3 0.7 to 1.1 c case size avx tps 0.2 (typ) 0.5 (typ) many engineers have heard that solid tantalum capacitors are prone to failure if they undergo high surge currents. this is historically true, and type tps capacitors are specially tested for surge capability, but surge ruggedness is not a critical issue with the output capacitor. solid tantalum applications information downloaded from: http:///
lt1766/lt1766-5 16 1766fc input capacitor step-down regulators draw current from the input supply in pulses. the rise and fall times of these pulses are very fast. the input capacitor is required to reduce the voltage ripple this causes at the input of lt1766 and force the switching current into a tight local loop, thereby minimizing emi. the rms ripple current can be calculated from: ii v v v v ripple rms out out in out in () = () ?/ 2 ceramic capacitors are ideal for input bypassing. at 200khz switching frequency, the energy storage requirement of the input capacitor suggests that values in the range of 2.2f to 20f are suitable for most applications. if operation is required close to the minimum input required by the output of the lt1766, a larger value may be required. this is to prevent excessive ripple causing dips below the minimum operating voltage resulting in erratic operation. depending on how the lt1766 circuit is powered up you may need to check for input voltage transients. the input voltage transients may be caused by input volt- age steps or by connecting the lt1766 converter to an already powered up source such as a wall adapter. the sudden application of input voltage will cause a large surge of current in the input leads that will store energy in the parasitic inductance of the leads. this energy will cause the input voltage to swing above the dc level of input power source and it may exceed the maximum voltage rating of input capacitor and lt1766. the easiest way to suppress input voltage transients is to add a small aluminum electrolytic capacitor in parallel with the low esr input capacitor. the selected capacitor needs to have the right amount of esr in order to criti- cally dampen the resonant circuit formed by the input lead inductance and the input capacitor. the typical values of esr will fall in the range of 0.5 to 2 and capacitance will fall in the range of 5f to 50f. if tantalum capacitors are used, values in the 22f to 470f range are generally needed to minimize esr and meet ripple current and surge ratings. care should be taken to ensure the ripple and surge ratings are not exceeded. the avx tps and kemet t495 series are surge rated. avx recommends derating capacitor operating voltage by 2:1 for high surge applications. catch diode highest ef? ciency operation requires the use of a schottky type diode. dc switching losses are minimized due to its low forward voltage drop, and ac behavior is benign due to its lack of a signi? cant reverse-recovery time. schottky diodes are generally available with reverse-voltage ratings of up to 60v and even 100v, and are price competitive with other types. the use of so-called ultrafast recovery diodes is generally not recommended. when operating in continuous mode, the reverse-recovery time exhibited by ultrafast diodes will result in a slingshot type effect. the power internal switch will ramp up v in current into the diode in an attempt to get it to recover. then, when the diode has ? nally turned off, some tens of nanoseconds later, the v sw node volt- age ramps up at an extremely high dv/dt, perhaps 5 to even 10v/ns ! with real world lead inductances, the v sw node can easily overshoot the v in rail. this can result in poor rfi behavior and if the overshoot is severe enough, damage the ic itself. the suggested catch diode (d1) is an international recti? er 10mq060n schottky. it is rated at 1.5a average forward current and 60v reverse voltage. typical forward voltage is 0.63v at 1a. the diode conducts current only during switch off time. peak reverse voltage is equal to regulator input voltage. average forward current in normal operation can be calculated from: i ivv v davg out in out in () ? = () this formula will not yield values higher than 1.5a with maximum load current of 1.5a. the only reason to consider a larger diode is the worst-case condition of a high input voltage and shorted output. with a shorted condition, diode current will increase to a typical value of 2a, determined by peak switch current limit. this is safe for short periods of time, but it would be prudent to check with the diode manufacturer if continuous operation under these conditions must be tolerated. applications information downloaded from: http:///
lt1766/lt1766-5 17 1766fc applications information boost pin for most applications, the boost components are a 0.33f capacitor and a 1n4148w diode. the anode is typically connected to the regulated output voltage to generate a voltage approximately v out above v in to drive the output stage. however, the output stage discharges the boost ca- pacitor during the on time of the switch. the output driver requires at least 3v of headroom throughout this period to keep the switch fully saturated. if the output voltage is less than 3.3v, it is recommended that an alternate boost supply is used. the boost diode can be connected to the input, although, care must be taken to prevent the 2 v in boost voltage from exceeding the boost pin absolute maximum rating. the additional voltage across the switch driver also increases power loss, reducing ef? ciency. if available, and independent supply can be used with a local bypass capacitor. a 0.33f boost capacitor is recommended for most ap- plications. almost any type of ? lm or ceramic capacitor is suitable, but the esr should be <1 to ensure it can be fully recharged during the off time of the switch. the capacitor value is derived from worst-case conditions of 4700ns on time, 42ma boost current and 0.7v discharge ripple. the boost capacitor value could be reduced under less demanding conditions, but this will not improve cir- cuit operation or ef? ciency. under low input voltage and low load conditions, a higher value capacitor will reduce discharge ripple and improve start-up operation. shutdown function and undervoltage lockout figure 4 shows how to add undervoltage lockout (uvlo) to the lt1766. typically, uvlo is used in situations where the input supply is current limited , or has a relatively high source resistance. a switching regulator draws constant power from the source, so source current increases as source voltage drops. this looks like a negative resistance load to the source and can cause the source to current limit or latch low under low source voltage conditions. uvlo prevents the regulator from operating at source voltages where these problems might occur. threshold voltage for lockout is about 2.38v. a 5.5a bias current ? ows out of the pin at this threshold. the internally generated current is used to force a default high state on the shutdown pin if the pin is left open. when low shutdown current is not an issue, the error due to this current can be minimized by making r lo 10k or less. if shutdown current is an issue, r lo can be raised to 100k, but the error due to initial bias current and changes with temperature should be considered. rkr rv v vr a lohi lo in lo = () = () () 10 238 238 55 to 100k 25k suggested . .. v in = minimum input voltage C + C + 2.38v 0.4v gnd v sw lt1766 input r fb l1 c1 r hi 1766 f04 output shdn standby in totalshutdown 5.5a r lo c2 + figure 4. undervoltage lockout downloaded from: http:///
lt1766/lt1766-5 18 1766fc keep the connections from the resistors to the shutdown pin short and make sure that interplane or surface ca- pacitance to the switching nodes are minimized. if high resistor values are used, the shutdown pin should be bypassed with a 1000pf capacitor to prevent coupling problems from the switch node. if hysteresis is desired in the undervoltage lockout point, a resistor, r fb , can be added to the output node. resistor values can be calculated from: r rv vv v ra rrv v hi lo in out lo fb hi out = + () + [] () = () () 238 1 238 55 ./ .. / ? 25k suggested for r lo v in = input voltage at which switching stops as input voltage descends to trip level v = hysteresis in input voltage level example: output voltage is 5v, switching is to stop if input voltage drops below 12v and should not restart unless input rises back to 13.5v. v is therefore 1.5v and v in = 12v. let r lo = 25k. r k ka k k rk k hifb = + () + [] () = () = = () = 25 12 2 38 1 5 5 1 1 5 238 25 55 25 10 41 224 116 116 5 1 5 387 ../ . .? . . . /. synchronizing the sync input must pass from a logic level low, through the maximum synchronization threshold with a duty cycle between 10% and 90%. the input can be driven directly from a logic level output. the synchronizing range is equal to initial operating frequency up to 700khz. this means that minimum practical sync frequency is equal to the worst-case high self-oscillating frequency (228khz), not the typical operating frequency of 200khz. caution should be used when synchronizing above 265khz because at higher sync frequencies the amplitude of the internal slope compensation used to prevent subharmonic switching is reduced. this type of subharmonic switching only occurs at input voltages less than twice output voltage. higher inductor values will tend to eliminate this problem. see frequency compensation section for a discussion of an entirely different cause of subharmonic switching before assuming that the cause is insuf? cient slope compensa- tion. application note 19 has more details on the theory of slope compensation. at power-up, when v c is being clamped by the fb pin (see figure 2, q2), the sync function is disabled. this allows the frequency foldback to operate in the shorted output condition. during normal operation, switching frequency is controlled by the internal oscillator until the fb pin reaches 0.6v, after which the sync pin becomes operational. if no synchronization is required, this pin should be connected to ground. layout considerations as with all high frequency switchers, when considering layout, care must be taken in order to achieve optimal electrical, thermal and noise performance. for maxi- mum ef? ciency, switch rise and fall times are typically in the nanosecond range. to prevent noise both radiated and conducted, the high speed switching current path, shown in figure 5, must be kept as short as possible. this is implemented in the suggested layout of figure 6. shortening this path will also reduce the parasitic trace inductance of approximately 25nh/inch. at switch off, this parasitic inductance produces a ? yback spike across the lt1766 switch. when operating at higher currents and input voltages, with poor layout, this spike can generate voltages across the lt1766 that may exceed its absolute 1766 f05 5v l1 v in lt1766 d1 c1 c3 high frequency circulating path load figure 5. high speed switching path applications information downloaded from: http:///
lt1766/lt1766-5 19 1766fc applications information maximum rating. a ground plane should always be used under the switcher circuitry to prevent interplane coupling and overall noise. the v c and fb components should be kept as far away as possible from the switch and boost nodes. the lt1766 pinout has been designed to aid in this. the ground for these components should be separated from the switch current path. failure to do so will result in poor stability or subharmonic like oscillation. board layout also has a signi? cant effect on thermal resistance. pins 1, 8, 9 and 16, gnd, are a continuous copper plate that runs under the lt1766 die. this is the best thermal path for heat out of the package. reducing the thermal resistance from pins 1, 8, 9 and 16 onto the board will reduce die temperature and increase the power capability of the lt1766. this is achieved by providing as much copper area as possible around these pins. add- ing multiple solder ? lled feedthroughs under and around these four corner pins to the ground plane will also help. similar treatment to the catch diode and coil terminations will reduce any additional heating effects. for the fe pack-age, the exposed pad (pin 17) should be soldered to the copper ground plane underneath the device. parasitic resonance resonance or ringing may sometimes be seen on the switch node (see figure 7). very high frequency ringing following switch rise time is caused by switch/diode/input capacitor lead inductance and diode capacitance. schottky diodes have very high q junction capacitance that can ring for many cycles when excited at high frequency. if total lead length for the input capacitor, diode and switch path is 1 inch, the inductance will be approximately 25nh. at switch off, this will produce a spike across the npn output device in addition to the input voltage. at higher currents this spike can be in the order of 10v to 20v or higher with a poor layout, potentially exceeding the abso lute max switch voltage. the path around switch, catch diode and input capacitor must be kept as short as possible to ensure reliable operation. when looking at this, figure 6. suggested layout gnd gnd shdn sync gnd boost v in sw place feedthrough around ground pins (4 corners) for good thermal conductivity lt1766 c3 c1 d1 c2 d2 r2 r1 1766 f06 c fb c f r c c c l1 minimize lt1766 c3-d1 loop gnd gnd bias fb v c connect to ground plane kelvin sense v out keep fb and v c components away from high frequency,high current components for the fe package, theexposed pad (pin 17) should be properly soldered to the ground plane. note: boost and bias copper traces are on a separate layer from the ground plane gnd v out v in 12 3 4 5 6 7 8 1615 14 13 12 11 10 9 downloaded from: http:///
lt1766/lt1766-5 20 1766fc applications information a >100mhz oscilloscope must be used, and waveforms should be observed on the leads of the package. this switch off spike will also cause the sw node to go below ground. the lt1766 has special circuitry inside which mitigates this problem, but negative voltages over 0.8v lasting longer than 10ns should be avoided. note that 100mhz oscilloscopes are barely fast enough to see the details of the falling edge overshoot in figure 7. a second, much lower frequency ringing is seen during switch off-time if load current is low enough to allow the inductor current to fall to zero during part of the switch off-time (see figure 8). switch and diode capacitance resonate with the inductor to form damped ringing at 1mhz to 10 mhz. this ringing is not harmful to the regulator and it has not been shown to contribute signi? cantly to emi. any attempt to damp it with a resistive snubber will degrade ef? ciency. thermal calculations power dissipation in the lt1766 chip comes from four sources: switch dc loss, switch ac loss, boost circuit cur- rent, and input quiescent current. the following formulas show how to calculate each of these losses. these formulas assume continuous mode operation, so they should not be used for calculating ef? ciency at light load currents. switch loss: p ri v v tiv f sw sw out out in eff out in = () ( ) + () () ( ) 2 12 (/ ) boost current loss: p vi v boost out out in = () 2 36/ quiescent current loss: pv v q in out = () + () 0 0015 0 003 .. r sw = switch resistance ( 0.3) hot t eff = effective switch current/voltage overlap time = (t r + t f + t ir + t if ) t r = (v in /1.2)ns t f = (v in /1.7)ns t ir = t if = (i out /0.05)ns f = switch frequency example: with v in = 40v, v out = 5v and i out = 1a: figure 8. discontinuous mode ringing 1s/div v in = 40v v out = 5v l = 47h 10v/div switch nodevoltage inductor current at i out = 0.1a 0.2a/div 1766 f08 figure 7. switch node resonance 50ns/div 1766 f07 2v/div sw rise sw fall p w pwpw sw boost q = () ()() + () () ()( ) () =+ = = () () = =+= 03 1 5 40 97 10 1 2 1 40 200 10 004 0388 043 5136 40 002 40 0 0015 5 0 003 0 08 2 93 2 . ?/ ? .. . / . (. ) (. ) . total power dissipation in the ic is given by: p tot = p sw + p boost + p q = 0.43w + 0.02w + 0.08w = 0.53w downloaded from: http:///
lt1766/lt1766-5 21 1766fc thermal resistance for the lt1766 packages is in? uenced by the presence of internal or backside planes.ssop (gn16) package: with a full plane under the gn16 package, thermal resistance will be about 85c/w. tssop (exposed pad) package: with a full plane under the tssop package, thermal resistance will be about 45c/w. to calculate die temperature, use the proper thermal resistance number for the desired package and add in worst-case ambient temperature: t j = t a + ( ja ? p tot ) when estimating ambient, remember the nearby catch diode and inductor will also be dissipating power: p vv v i v diode f in out load in = ( )( ? )( ) v f = forward voltage of diode (assume 0.63v at 1a) pw diode == (. )( ? )() . 063 40 5 1 40 055 p inductor = (i load ) 2 (r l ) r l = inductor dc resistance (assume 0.1) p inductor (1) 2 (0.1) = 0.1w only a portion of the temperature rise in the external inductor and diode is coupled to the junction of the lt1766. based on empirical measurements the thermal effect on lt1766 junction temperature due to power dissipation in the external inductor and catch diode can be calculated as: t j (lt1766) (p diode + p inductor )(10c/w) using the example calculations for lt1766 dissipation, the lt1766 die temperature will be estimated as: t j = t a + ( ja ? p tot ) + [10 ? (p diode + p inductor )] with the gn16 package ( ja = 85c/w), at an ambient temperature of 60c: t j = 60 + (85 ? 0.53) + (10 ? 0.65) = 112c with the tssop package ( ja = 45c/w), at an ambient temperature of 60c: t j = 60 + (45 ? 0.53) + (10 ? 0.65) = 90c die temperature can peak for certain combinations of v in , v out and load current. while higher v in gives greater switch ac losses, quiescent and catch diode losses, a lower v in may generate greater losses due to switch dc losses. in general, the maximum and minimum v in levels should be checked with maximum typical load current for calculation of the lt1766 die temperature. if a more accurate die temperature is required, a measurement of the sync pin resistance (to gnd) can be used. the sync pin resistance can be measured by forcing a voltage no greater than 0.5v at the pin and monitoring the pin cur- rent over temperature in an oven. this should be done with minimal device power (low v in and no switching (v c = 0v)) in order to calibrate sync pin resistance with ambient (oven) temperature. note: some of the internal power dissipation in the ic, due to boost pin voltage, can be transferred outside of the ic to reduce junction temperature, by increasing the voltage drop in the path of the boost diode d2 (see figure 9). this reduction of junction temperature inside the ic will allow higher ambient temperature operation for a given set of conditions. boost pin circuitry dissipates power given by: p vi v v diss boost out sw c in () ?( / )? = 36 2 typically v c2 (the boost voltage across the capacitor c2) equals vout. this is because diodes d1 and d2 can be considered almost equal, where: v c2 = v out C v fd2 C (Cv fd1 ) = v out hence the equation used for boost circuitry power dissi- pation given in the previous thermal calculations section is stated as: p vi v v diss boost out sw out in () ?( / )? = 36 here it can be seen that boost power dissipation increases as the square of v out . it is possible, however, to reduce v c2 below v out to save power dissipation by increasing the voltage drop in the path of d2. care should be taken that v c2 does not fall below the minimum 3.3v boost voltage required for full saturation of the internal power switch. applications information downloaded from: http:///
lt1766/lt1766-5 22 1766fc applications information for an fe package with thermal resistance of 45c/w, ambient temperature savings would be, t(ambient) savings = 0.116w ? 45c/w = 5c. for a gn package with thermal resistance of 85c/w, ambient temperature savings would be t/(ambient) savings = 0.116 ? 85c/w = 10c. the 7v zener should be sized for excess of 0.116w operation. the tolerances of the zener should be considered to ensure minimum v c2 exceeds 3.3v + v droop . input voltage vs operating frequency considerations the absolute maximum input supply voltage for the lt1766 is speci? ed at 60v. this is based solely on internal semiconductor junction breakdown effects. due to internal power dissipation, the actual maximum v in achievable in a particular application may be less than this.a detailed theoretical basis for estimating internal power loss is given in the section, thermal considerations. note that ac switching loss is proportional to both operating frequency and output current. the majority of ac switching loss is also proportional to the square of input voltage. for example, while the combination of v in = 40v, v out = 5v at 1a and f osc = 200khz may be easily achievable, simultaneously raising v in to 60v and f osc to 700khz is not possible. nevertheless, input voltage transients up to 60v can usually be accommodated, assuming the result-ing increase in internal dissipation is of insuf? cient time duration to raise die temperature signi? cantly. a second consideration is controllability. a potential limita- tion occurs with a high step-down ratio of v in to v out , as this requires a correspondingly narrow minimum switch on time. an approximate expression for this (assuming continuous mode operation) is given as follows: min t vv vf on out f in osc = + () where: v in = input voltage v out = output voltage v f = schottky diode forward drop f osc = switching frequency a potential controllability problem arises if the lt1766 is called upon to produce an on time shorter than it is able to produce. feedback loop action will lower then reduce for output voltages of 5v, v c2 is approximately 5v. during switch turn on, v c2 will fall as the boost capacitor c2 is dicharged by the boost pin. in the previous boost pin section, the value of c2 was designed for a 0.7v droop in v c2 = v droop . hence, an output voltage as low as 4v would still allow the minimum 3.3v for the boost function using the c2 capacitor calculated. if a target output voltage of 12v is required, however, an excess of 8v is placed across the boost capacitor which is not required for the boost function but still dissipates additional power. what is required is a voltage drop in the path of d2 to achieve minimal power dissipation while still maintaining minimum boost voltage across c2. a zener, d4, placed in series with d2 (see figure 9), drops voltage to c2. example : the boost pin power dissipation for a 20v input to 12v output conversion at 1a is given by: pw boost == 12 1 36 12 20 02 ?( / )? . if a 7v zener d4 is placed in series with d2, then power dissipation becomes : pw boost == 12 1 36 5 20 0 084 ?( / )? . boost v in d1 r1 v out c f c c lt1766 shdnsync sw bias fb v c gnd c2 c1 l1 d2 r2 1766 f09 c3 v in d2 d4 + r c figure 9. boost pin, diode selection downloaded from: http:///
lt1766/lt1766-5 23 1766fc applications information the v c control voltage to the point where some sort of cycle-skipping or odd/even cycle behavior is exhibited. in summary: 1. be aware that the simultaneous requirements of high v in , high i out and high f osc may not be achievable in practice due to internal dissipation. the thermal con-siderations section offers a basis to estimate internal power. in questionable cases a prototype supply should be built and exercised to verify acceptable operation. 2. the simultaneous requirements of high v in , low v out and high f osc can result in an unacceptably short minimum switch on-time. cycle skipping and/or odd/even cycle behavior will result although correct output voltage is usually maintained. frequency compensation before starting on the theoretical analysis of frequency response, the following should be rememberedthe worse the board layout, the more dif? cult the circuit will be to stabilize. this is true of almost all high frequency analog circuits, read the layout considerations section ? rst. common layout errors that appear as stability prob- lems are distant placement of input decoupling capacitor and/or catch diode, and connecting the v c compensation to a ground track carrying signi? cant switch current. in addition, the theoretical analysis considers only ? rst order non-ideal component behavior. for these reasons, it is important that a ? nal stability check is made with produc- tion layout and components. the lt1766 uses current mode control. this alleviates many of the phase shift problems associated with the inductor. the basic regulator loop is shown in figure 10. the lt1766 can be considered as two g m blocks, the error ampli? er and the power stage. figure 11 shows the overall loop response. at the v c pin, the frequency compensation components used are: r c = 2.2k, c c = 0.022f and c f = 220pf. the output capacitor used is a 100f, 10v tantalum capacitor with typical esr of 100m. the esr of the tantalum output capacitor provides a use-ful zero in the loop frequency response for maintaining stability. this esr, however, contributes signi? cantly to the ripple voltage at the output (see output ripple volt- age in the applications section). it is possible to reduce capacitor size and output ripple voltage by replacing the tantalum output capacitor with a ceramic output capaci- tor because of its very low esr. the zero provided by the tantalum output capacitor must now be reinserted back into the loop. alternatively there may be cases where, even with the tantalum output capacitor, an additional zero is required in the loop to increase phase margin for improved transient response. a zero can be added into the loop by placing a resistor, r c, at the v c pin in series with the compensation capaci- tor, c c or by placing a capacitor, c fb , between the output and the fb pin. frequency (hz) gain (db) 8060 40 20 0 C20C40 phase (deg) 180150 120 90 60 30 0 1766 f11 gain phase 10 v in = 42v v out = 5v i load = 500ma c out = 100f, 10v, 0.1 1k 10k 1m 100 100k r c = 2.2k c c = 22nf c f = 220pf figure 11. overall loop response C + 1.22v v sw v c lt1766 gnd 1766 f10 r1 output esr c f c c r c r o 200k error amplifier fb r2 c1 r load current mode power stage g m = 2mho g m = 2000mho + tantalum c fb ceramic esl c1 figure 10. model for loop response downloaded from: http:///
lt1766/lt1766-5 24 1766fc when using r c , the maximum value has two limitations. first, the combination of output capacitor esr and r c may stop the loop rolling off altogether. second, if the loop gain is not rolled off suf? ciently at the switching frequency, output ripple will peturb the v c pin enough to cause unstable duty cycle switching similar to subharmonic oscillations. if needed, an additional capacitor, c f , can be added across the r c /c c network from the v c pin to ground to further suppress v c ripple voltage. with a tantalum output capacitor, the lt1766 already in- cludes a resistor, r c and ? lter capacitor, c f , at the v c pin (see figures 10 and 11) to compensate the loop over the entire v in range (to allow for stable pulse skipping for high v in -to-v out ratios 10). a ceramic output capacitor can still be used with a simple adjustment to the resistor r c for stable operation. (see ceramic capacitors section for stabilizing lt1766). if additional phase margin is required, a capacitor, c fb , can be inserted between the output and fb pin but care must be taken for high output voltage applica-tions. sudden shorts to the output can create unacceptably large negative transients on the fb pin. for v in -to-v out ratios <10, higher loop bandwidths are possible by readjusting the frequency compensation components at the v c pin. when checking loop stability, the circuit should be op- erated over the applicationss full voltage, current and temperature range. proper loop compensation may be obtained by emperical methods as described in detail in application notes 19 and 76. converter with backup output regulator in systems with a primary and backup supply, for example, a battery-powered device with a wall adapter input, the output of the lt1766 can be held up by the backup supply with the lt1766 input disconnected. in this condition, the sw pin will source current into the v in pin. if the shdn pin is held at ground, only the shut down current of 25a will be pulled via the sw pin from the second supply. with the shdn pin ? oating, the lt1766 will consume its quiescent operating current of 1.5ma. the v in pin will also source current to any other components connected to the input line. if this load is greater than 10ma or the input could be shorted to ground, a series schottky diode must be added, as shown in figure 12. with these safeguards, the output can be held at voltages up to the v in absolute maximum rating. buck converter with adjustable soft-start large capacitive loads or high input voltages can cause high input currents at start-up. figure 13 shows a circuit that limits the dv/dt of the output at start-up, controlling the capacitor charge rate. the buck converter is a typical con? guration with the addition of r3, r4, c ss and q1. as the output starts to rise, q1 turns on, regulating switch current via the v c pin to maintain a constant dv/dt at the output. output rise time is controlled by the current through c ss de? ned by r4 and q1s v be . once the output is in regulation, q1 turns off and the circuit operates normally. r3 is transient protection for the base of q1. 5v, 1a removable input c2 0.33f c f 220pf r354k d110mq060n 1766 f12 c32.2f r c 2.2k c c 0.022f d3 10mq060n d2 1n4148w l1 47h c1100f 10v alternate supply r425k r115.4k r24.99k boost v in lt1766 shdn sync sw bias fb v c gnd + figure 12. dual source supply with 25a reverse leakage applications information downloaded from: http:///
lt1766/lt1766-5 25 1766fc risetime rc v v ss out be = () ( ) ( ) 4 using the values shown in figure 10, rise time ms = () ( ) () = 47 10 15 10 5 07 5 39 ?? . ? the ramp is linear and rise times in the order of 100ms are possible. since the circuit is voltage controlled, the ramp rate is unaffected by load characteristics and maximum output current is unchanged. variants of this circuit can be used for sequencing multiple regulator outputs. dual output sepic converter the circuit in figure 14 generates both positive and nega- tive 5v outputs with a single piece of magnetics. the two inductors shown are actually just two windings on a stan- dard coiltronics inductor. the topology for the 5v output is a standard buck converter. the C 5v topology would be a simple ? yback winding coupled to the buck converter if c4 were not present. c4 creates a sepic (single-ended primary inductance converter) topology which improves regulation and reduces ripple current in l1. without c4, the voltage swing on l1b compared to l1a would vary due to relative loading and coupling losses. c4 provides a low impedance path to maintain an equal voltage swing in l1b, improving regulation. in a ? yback converter, during switch on-time, all the converters energy is stored in l1a only, since no current ? ows in l1b. at switch off, energy v out1 5v(see dn100 for max i out ) v out2 C5v ? * l1 is a single core with two windings coiltronics #ctx50-3a ? if load can go to zero, an optional preload of 1k to 5k may be used to improve load regulation d1, d3: 10mq060n v in 7.5v to 60v gnd 1766 f14 c2 0.33f c f 220pf d1 c1100f 10v tant c5 100f 10v tant c3 2.2f 100v cer c4 100f 10v tant d2 1n4148w d3 l1a* 50h l1b* r1 15.4k r2 4.99k + + + r c 2.2k c c 0.022f boost v in lt1766 shdnsync sw fb v c gnd figure 14. dual output sepic converter output 5v1a input 40v 1766 f13 c20.33f c1 100f c ss 15nf c f 220pf d1 c32.2f 50v cer d2 1n4148w l1 47h r115.4k r3 2k c c 0.022f r24.99k r447k q1 boost bias v in lt1766 shdn sync sw fb v c gnd + r c 2.2k figure 13. buck converter with adjustable soft-start is transferred by magnetic coupling into l1b, powering the C5v rail. c4 pulls l1b positive during switch on-time, causing current to ? ow, and energy to build in l1b and c4. at switch off, the energy stored in both l1b and c4 supply the C5v rail. this reduces the current in l1a and changes l1b current waveform from square to triangular. for details on this circuit, including maximum output cur- rents, see design note 100. positive-to-negative converter the circuit in figure 15 is a positive-to-negative topology using a grounded inductor. it differs from the standard approach in the way the ic chip derives its feedback signal because the lt1766 accepts only positive feedback signals. the ground pin must be tied to the regulated negative output. a resistor divider to the fb pin then provides the proper feedback voltage for the chip. the following equation can be used to calculate maximum load current for the positive-to-negative converter: i i vv vvf l vv vv vv max p in out out in out in out in out f = + ?? ? ?? ? ++ ? ()( ) () ( ) ( ) () (?. ) (? . ) () 2 03 03 applications information downloaded from: http:///
lt1766/lt1766-5 26 1766fc applications information i p = maximum rated switch current v in = minimum input voltage v out = output voltage v f = catch diode forward voltage 0.3 = switch voltage drop at 1.5a example: with v in(min) = 5.5v, v out = 12v, l = 18h, v f = 0.63v, i p = 1.5a: i max = 0.280a. output divider refer to applications information feedback pin functions to calculate r1 and r2 for the (negative) output voltage (from table 1). mode formula to calculate minimum inductor needed. if load current is higher, use the continuous mode formula. output current where continuous mode is needed: i vi vv vv v cont in p in out in out f > ++ + ()() () ( ) 22 4 minimum inductor discontinuous mode: l vi fi min out out p = 2 2 () () ()( ) minimum inductor continuous mode: l vv fv v i i vv v min in out in out p out out f in = ++ + ?? ? ?? ? ?? ? ?? ? ()( ) ()( ) ? () 21 for a 40v to C12v converter using the lt1766 with peak switch current of 1.5a and a catch diode of 0.63v: ia cont > ++ + = ()(.) () ( . ) . 40 1 5 440124012063 0 573 22 for a load current of 0.25a, this says that discontinuous mode can be used and the minimum inductor needed is found from: lh min == 212 025 200 10 1 5 13 3 32 ()(.) (?) (.) . in practice, the inductor should be increased by about 30% over the calculated minimum to handle losses and variations in value. this suggests a minimum inductor of 18h for this application. ripple current in the input and output capacitors positive-to-negative converters have high ripple current in the input capacitor. for long capacitor lifetime, the rms value of this current must be less than the high frequency ripple current rating of the capacitor. the following formula will give an approximate value for rms ripple current. this formula assumes continuous mode and large inductor value . small inductors will give somewhat higher ripple current, especially in discontinuous mode. the exact formulas are very complex and appear in application output**C12v, 0.25a input ? 5.5v to 48v 1766 f15 c20.33f c c r c d110mqo60n r1 44.2k c1100f 25v tant c3 2.2f 100v cer d2 ? 1n4148w l1* 18h c f boost lt1766 v in v sw fb gnd v c r24.99k * increase l1 to 30h or 60h for higher current applications. see applications information ** maximum load current depends on minimum input voltage and inductor size. see applications information ? for v in > 44v and v out = C12v, additional voltage drop in the path of d2 is required to ensure boost pin maximum rating is not exceeded. see applications information (boost pin voltage) + figure 15. positive-to-negative converter inductor value the criteria for choosing the inductor is typically based on ensuring that peak switch current rating is not exceeded. this gives the lowest value of inductance that can be used, but in some cases (lower output load currents) it may give a value that creates unnecessarily high output ripple voltage. the dif? culty in calculating the minimum inductor size needed is that you must ? rst decide whether the switcher will be in continuous or discontinuous mode at the critical point where switch current reaches 1.5a. the ? rst step is to use the following formula to calculate the load current above which the switcher must use continuous mode. if your load current is less than this, use the discontinuous downloaded from: http:///
lt1766/lt1766-5 27 1766fc note 44, pages 29 and 30. for our purposes here a fudge factor (ff) is used. the value for ff is about 1.2 for higher load currents and l 15h. it increases to about 2.0 for smaller inductors at lower load currents. input capacitor i ff i v v rms out out in = ()( ) ff = 1.2 to 2.0the output capacitor ripple current for the positive-to- negative converter is similar to that for a typical buck regulatorit is a triangular waveform with peak-to-peak value equal to the peak-to-peak triangular waveform of the inductor. the low output ripple design in figure 15 places the input capacitor between v in and the regulated negative output. this placement of the input capacitor signi? cantly reduces the size required for the output capacitor (versus placing the input capacitor between v in and ground). the peak-to-peak ripple current in both the inductor and output capacitor (assuming continuous mode) is: i p-p p-p = == + ++ = dc v fl dc duty cycle vv vvv i rms i in out f out in f cout ? ? () 12 the output ripple voltage for this con? guration is as low as the typical buck regulator based predominantly on the inductors triangular peak-to-peak ripple current and the esr of the chosen capacitor (see output ripple voltage in applications information). diode current average diode current is equal to load current. peak diode current will be considerably higher. peak diode current: continuous mode i vv v vv lfv v discontinuous mode iv lf out in out in in out in out out out = + + + = () ( ) ( ) ()()( ) () ( ) ()() 2 2 keep in mind that during start-up and output overloads, average diode current may be much higher than with nor- mal loads. care should be used if diodes rated less than 1a are used, especially if continuous overload conditions must be tolerated. boost pin voltage to ensure that the boost pin voltage does not exceed its absolute maximum rating of 68v with respect to device gnd pin voltage, care should be taken in the generation of boost voltage. for the conventional method of generating boost voltage, shown in figure 1, the voltage at the boost pin during switch on time is approximately given by: v boost (gnd pin) = (v in C v gndpin ) + v c2 where: v c2 = (d2+) C v d2 C (d1+) + v d1 = voltage across the boost capacitor for the positive-to-negative converter shown in figure 15, the conventional buck output node is grounded (d2+) = 0v and the catch diode (d1+) is connected to the negative output = v out = C12v. absolute maximum ratings should also be observed with the gnd pin now at C12v. it can be seen that for v d1 = v d2 : v c2 = (d2+) C (d1+) = |v out | = 12v the maximum v in voltage allowed for the device (gnd pin at C12v) is 48v. the maximum v in voltage allowed without exceeding the boost pin voltage absolute maximum rating is given by: v in(max) = boost (max) + (v gndpin ) C v c2 v in(max) = 68 + (C12) C 12 = 44v to increase usable v in voltage, v c2 must be reduced. this can be achieved by placing a zener diode v z1 (anode at c2+) in series with d2. note: a maximum limit on v z1 must be observed to ensure a minimum v c2 is maintained on the boost capacitor; referred to as v boost(min) in the electrical characteristics. applications information downloaded from: http:///
lt1766/lt1766-5 28 1766fc package description fe package 16-lead plastic tssop (4.4mm) (reference ltc dwg # 05-08-1663) exposed pad variation bb gn package 16-lead plastic ssop (narrow .150 inch) (reference ltc dwg # 05-08-1641) fe16 (bb) tssop 0204 0.09 C 0.20 (.0035 C .0079) 0 o C 8 o 0.25 ref 0.50 C 0.75 (.020 C .030) 4.30 C 4.50* (.169 C .177) 1.10 (.0433) max 0.05 C 0.15 (.002 C .006) 0.65 (.0256) bsc 0.195 C 0.30 (.0077 C .0118) typ millimeters (inches) *dimensions do not include mold flash. mold flash shall not exceed 0.150mm (.006") per side note:1. controlling dimension: millimeters 2. dimensions are in 3. drawing not to scale recommended solder pad layout 0.45 p 0.05 0.65 bsc 4.50 p 0.10 6.60 p 0.10 1.05 p 0.10 2.94 (.116) 3.58 (.141) see note 4 4. recommended minimum pcb metal size for exposed pad attachment 134 5 6 7 8 10 9 4.90 C 5.10* (.193 C .201) 16 1514 13 12 11 2.94 (.116) 2 3.58 (.141) 6.40 (.252) bsc gn16 (ssop) 0204 .016 C .050 (0.406 C 1.270) .015 p .004 (0.38 p 0.10) s 45 o 0 o C 8 o typ .007 C .0098 (0.178 C 0.249) .0532 C .0688 (1.35 C 1.75) .008 C .012 (0.203 C 0.305) typ .004 C .0098 (0.102 C 0.249) .0250 (0.635) bsc 12 3 4 5 6 7 8 .229 C .244 (5.817 C 6.198) .150 C .157** (3.810 C 3.988) 16 15 14 13 .189 C .196* (4.801 C 4.978) 12 11 10 9 .009 (0.229) ref .254 min recommended solder pad layout .150 C .165 .0250 bsc .0165 p .0015 .045 p .005 * dimension does not include mold flash. mold flash shall not exceed 0.006" (0.152mm) per side ** dimension does not include interlead flash. interlead flash shall not exceed 0.010" (0.254mm) per side inches (millimeters) note:1. controlling dimension: inches 2. dimensions are in 3. drawing not to scale downloaded from: http:///
lt1766/lt1766-5 29 1766fc information furnished by linear technology corporation is believed to be accurate and reliable. however, no responsibility is assumed for its use. linear technology corporation makes no representa- tion that the interconnection of its circuits as described herein will not infringe on existing patent rights. revision history rev date description page number c 03/10 removed lt1766hgn from order information 2 (revision history begins at rev c) downloaded from: http:///
lt1766/lt1766-5 30 1766fc linear technology corporation 1630 mccarthy blvd., milpitas, ca 95035-7417 (408) 432-1900 fax: (408) 434-0507 www.linear.com ? linear technology corporation 2001 lt/tp 0310 rev c printed in usa related parts part number description comments lt1074/lt1074hv 4.4a (i out ), 100khz, high ef? ciency step-down dc/dc converters v in : 7.3v to 45v/64v, v out(min) : 2.21v, i q : 8.5ma, i sd : 10a, dd-5/7, to220-5/7 lt1076/lt1076hv 1.6a (i out ), 100khz, high ef? ciency step-down dc/dc converters v in : 7.3v to 45v/64v, v out(min) : 2.21v, i q : 8.5ma, i sd : 10a, dd-5/7, to220-5/7 lt1616 500ma (i out ), 1.4mhz, high ef? ciency step-down dc/dc converter v in : 3.6v to 25v, v out(min) : 1.25v, i q : 1.9ma, i sd : <1a, thinsot? lt1676 60v, 440ma (i out ), 100khz, high ef? ciency step-down dc/dc converter v in : 7.4v to 60v, v out(min) : 1.24v, i q : 3.2ma, i sd : 2.5a, s8 lt1765 25v, 2.75a (i out ), 1.25mhz, high ef? ciency step-down dc/dc converter v in : 3v to 25v, v out(min) : 1.20v, i q : 1ma, i sd : 15a, s8, tssop16e lt1766 60v, 1.2a (i out ), 200khz, high ef? ciency step-down dc/dc converter v in : 5.5v to 60v, v out(min) : 1.20v, i q : 2.5ma, i sd : 25a, tssop16/e lt1767 25v, 1.2a (i out ), 1.25mhz, high ef? ciency step-down dc/dc converter v in : 3v to 25v, v out(min) : 1.20v, i q : 1ma, i sd : 6a, ms8/e lt1776 40v, 550ma (i out ), 200khz, high ef? ciency step-down dc/dc converter v in : 7.4v to 40v, v out(min) : 1.24v, i q : 3.2ma, i sd : 30a, n8,s8 lt1940 dual output 1.4a (i out ) , constant 1.1mhz, high ef? ciency step-down dc/dc converter v in : 3v to 25v, v out(min) : 1.20v, i q : 2.5ma, i sd : <1a, tssop-16e lt1956 60v, 1.2a (i out ), 500khz, high ef? ciency step-down dc/dc converter v in : 5.5v to 60v, v out(min) : 1.20v, i q : 2.5ma, i sd : 25a, tssop16/e lt1976 60v, 1.2a (i out ), 200khz, micropower (i q = 100a), high ef? ciency step-down dc/dc converter v in : 3.3v to 60v, v out(min) : 1.20v, i q : 100a, i sd : <1a, tssop16/e lt3010 80v, 50ma, low noise linear regulator v in : 1.5v to 80v, v out(min) : 1.28v, i q : 30a, i sd : <1a, ms8e ltc3412 2.5a (i out ), 4mhz, synchronous step-down dc/dc converter v in : 2.5v to 5.5v, v out(min) : 0.8v, i q : 60a, i sd : <1a, tssop16e ltc3414 4a (i out ), 4mhz, synchronous step-down dc/dc converter v in : 2.3v to 5.5v, v out(min) : 0.8v, i q : 64a, i sd : <1a, tssop20e lt3430/lt3431 60v, 2.75a (i out ), 200khz/500khz, high ef? ciency step-down dc/dc converters v in : 5.5v to 60v, v out(min) : 1.20v, i q : 2.5ma, i sd : 30a, tssop16e lt3433 high voltage, micropower (i q = 100a), buck-boost dc/dc converter v in : 4v to 60v, i q : 100a, 500ma switch current, tssop16e ltc3727/ltc3727-1 36v, 500khz, high ef? ciency step-down dc/dc controllers v in : 4v to 36v, v out(min) : 0.8v, i q : 670a, i sd : 20a, qfn-32, ssop-28 downloaded from: http:///

▲Up To Search▲

Price & Availability of LT1766EGNTRPBF

	To Download LT1766EGNTRPBF Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .